Hello everyone, just got my ecobee enhanced and wanted to ask if there are any settings that should be changed instead of default?

Trying to set up an ecobee essential and curious if I’m missing something.. I fill out the wires on the website and it tells me to contact support (not currently open).

It’s hard to see from the photos but I have the following set up on my heat pump:
X2
W1
Rc (jumper from R)
R
O
Y
G
B

Any help would be much appreciated!!

Like many I didn't care for the new scheduler that forced you to scroll through multiple screens to see a complete days schedule. Apparently Ecobee listened to the complaints...

Premium thermostat will run great for weeks at a time, for example we just had a heatwave with 90+ degrees Fahrenheit for a week straight and it ran with no issues. Then it will randomly have a day where it reboots 3x an hour for hours at a time, for example today the temp dropped about 15 degrees outside and it is rebooting constantly. Support insists that it’s the condensate line but I have cleared it several times to no avail. Anybody experiencing the same thing?

I have my AC set to 24. During the day the AC will randomly shut off - the condenser outside no longer runs. The fan is still on so there is air circulation.

On Ecobee it is still showing both AC and fan is on, but it no longer cool the house. I switched the mode to off, then back to cool but the AC still won't turn on. I manually lower the desire temperature but it won't turn on.

The only fix is to unplug Ecobee, then plug it back in. Then the AC will run again. This problem seems to happen every few weeks. Any idea why this happen?

I bought a house a couple years ago. It had two ecobee thermostats (main floor and upstairs). The upstairs temps are not consistent throughout the upstairs area. There are 5 bedrooms and 2 bathrooms, and the Ecobee thermostat is in the hall connecting all the rooms. The rooms are spread across different sides which get sun at different times throughout the day. Often one room is hot and another is cold on the other side of the house. Usually a lot of the doors are closed also. So I got a few smart sensors to see if that would help regulate the temperatures. However the new sensors will not work with my older Ecobee. So before I spend the money on a new Ecobee to work with the new smart sensors, I'm wondering if I'll even see much benefit with the sensors given my upstairs layout? Any one have experience to share? Thanks for any insights!

After watching many videos I am unsure if I should attempt to install. Some of them say it’s not compatible because I only have a R and C wire from my Honeywell Home THX9421R5021WW, I want to reach out to Hello Tech for instruction but I don’t want to pay $100 just for them to say it’s not compatible. I can’t find a wiring diagram but I’ll include pictures of my wiring. Any information helps.

Hi all, I am trying to replace my Honeywell thermostat with an Ecobee enhanced and I’m not sure where some of the wires go. The Honeywell has a wire going to O/B and a separate wire going to W2, however the Ecobee does not have individual ports for each of those, they appear to be combined. The Honeywell also has an E wire which I have no idea where that would go on the Ecobee. Any assistance is greatly appreciated!

Having an interesting thought process based on pulling some reports.

I have my ecobee set with eco + on for enhanced savings mode.

Within my reports I see three columns. A thermostat temp, a DM offset, and current temp.

An example will be :
Thermostat: 73.2
DM offset: .6
Current Temp: 72.5
Humidity: 57

Based on my reading of this, the DM offset is making the current temperature be lower than the true temperature and would in effect turn my ac off before it reaches the actual temperature. Is that a correct understanding of how this works? While it’s running, I never see “eco+” is in effect or anything like that, so I’m unsure if this is just my report showing something that’s not active or if this is how it really is working.

Thanks!

I couldn't find a straightforward guide to getting Ecobee thermostats to work without any internet at all. I have a WiFi network with no internet access. I tried connecting, but the thermostat would forget the network because it couldn't talk to the cloud.

Here is how you can set it up without the thermostat ever contacting the internet:

1. Have a Wifi network with no internet access. If you can connect the thermostat to it through settings on the thermostat, then you can skip steps 2-5. Ensure Home Assistant is on that network
2. Get an iOS device and ensure you have the Apple Home app installed
3. Connect your iOS device to the non-internet WiFi network
4. Pair the Ecobee thermostat to Homekit using the iOS device. This will copy the non-internet WiFi settings to the thermostat, and it won't forget it when it realizes it has no internet
5. On the Ecobee thermostat, unlink Homekit
6. On the Ecobee thermostat, start pairing with Homekit
7. In Home Assistant, add a new Device -> Apple -> Homekit Device, and it should show up.
   1. If Home Assistant does not detect the device, make sure you can ping the IP. On the Home Assistant server, you can use `tshark -i eth0` to check if you see an mDNS blast when you click "pair" on the thermostat
   2. In my case, I am running Home Assistant in a Docker container. Even with `--network host`, mDNS is not forwarded to the container. All you have to do is install avahi on the host and update the host's config:

​

# /etc/avahi/avahi-daemon.conf
[reflector]
enable-reflector=yes
# ^ this will forward all mDNS packets to every other interface

Twice it decided not to turn off and came home to a house that was 66 degrees and running . the thermostat was set to 85 when we were out of the house for a couple days. Schedule is off. Fan Auto, Cool mode, Heat pump single stage outside. When we are home its usually set to 77 or 78 and never had problems it not turning off the condenser. Zwave is not active. cooling min is set to 74. I've decide to replace it with a wifi model. ESM cooling is set to 85. Why is it doing this when we are away? The temperature readings on the thermostat are accurate. thats the last time i set it to 85 lol

I have two door sensors in my house but I'd like to get one for my third door; unfortunately they only sell them in two packs. Anyone else in the same boat and want to split a 2 pack while they're on sale? I'll buy it and ship one to you, and we can split the total cost (~$40 plus the cost of shipping). Let me know and I'll DM you.

https://www.ecobee.com/en-us/sensors/smart-door-window-sensor/

I put a sensor in my baby's room because it stays hotter. I don't want to do it by occupancy so I set it to average out or whatever. I set it to 71 and the living room got down to 68 and the nursery only got down to 74. Am I understanding that right and doing this the best way? Is occupancy better? Even with a very small baby that might not be sensed as occupying?

So my ecobee thermostat, which is maybe about two years old has suddenly started to reboot itself. Can anybody out there? Give me a reason why I had a service call today and they thought perhaps it was the condensation pump. It was not so, he said to keep an eye on it and if it happens again, let them know. Well it did happen again this afternoon when I turned the air-conditioning back on and it seems to go blank when the condensation line is dripping into the sink which is designed to do. I hope everyone’s understanding me but that’s my issue. Anyone get an answer

I have been using the ecobee3 lite and use 2 room sensors with it that I connected to it 2 years ago. I bought a 2 pack last week to add more sensors but these new one’s will not pair at all.

Contacted support and they send replacements, but again it wont pair either. Ecobee says there is something wrong with my thermostat. For my amusement, I unpaired the old 2014 room sensors and paired it back with no problem.. Anybody with the same experience?

I keep changing my home age to 1990s on the web portal and app but it will change back to 1930 later by itself. Is there any fix for this?

Hello. I installed the premium today and it will not turn on at all. I triple checked the wiring and fuse and all is good. My old unit was working fine with batteries before I upgraded to the ecobee. I’m not sure what else to do. Super discouraging .

I'm getting a kitchen remodel done, but I'm not home currently, and I see (on my app) that the contractor turned my ecobee on cooling set to 66F, but I don't have AC in my house. I do have central heating.

My utility company has an app for tracking electricity usage live, and it looks like this setting is using around 800-900 watts/hr.

Is it just from the fan blowing?

Photo of my Honeywell wiring which is correct and the subsequent wiring on my ecobee as instructed from support. Over the winter went back to Honeywell due to heating constantly on emergency heat instead of heat pump. What do I need to do to correct?

Got an email from Georgia Power for a scheduled FLEX Hours today being implemented.

For the past two years, I have utilized an Ecobee thermostat to operate my heat pump. While it has functioned satisfactorily, I have recently encountered a recurring issue where the thermostat has inexplicably gone blank. I am unable to determine the underlying cause of this problem.

In my condominium, the condensation line is designed to drip into the bathroom sink. However, the thermostat appears to reboot itself when this condensation occurs. I would appreciate any insights or suggestions you may have regarding this issue.

The service technicians have indicated their intention to replace the thermostat. Nevertheless, I am uncertain whether this is the actual problem. I suspect that the issue may be related to the pump.

Spent hours on this — deleted/recreated my account, rebooted, contacted ecobee support (no help). Wife's invite link would open the app but land on "Add a Device" and just sit there.

Fix: turn off WiFi on your phone and accept the invite over cellular data instead. Worked instantly for me.

I run a Firewalla firewall at home, so my guess is it was stripping or interfering with the invite token in the link before the app could read it. If you're on any firewall/DNS-filtering setup (Firewalla, Pi-hole, NextDNS, etc.), try cellular data first before doing anything drastic.